Ram Slot Soldering
Posted : admin On 3/27/2022Ram Slot Soldering Average ratng: 4,6/5 9038 votes
No it's about machines that are slimmer, lighter and far less likely to break, soldering RAM is easily the best option for all these reasons from an engineering point of view, when the amounts available are so large there is no need to upgrade and the benefits of soldered RAM far outweigh the ability to satisfy a few cheapskates.
- Before you spend any money or dig for a screw driver, the easiest way to check your laptop for open memory slots, or any memory slots at all (as opposed to RAM that’s soldered to motherboard.
- The BIOS wont recognize the 2 extra ram slots even if you manage to solder it (which you wont). Just save up and buy the ram you need, or save up to replace the whole motherboard.
sfbayzfs
Active Member
I have a lot of system building experience, and generally held the belief that bad RAM slots on motherboards are uncommon. The first one I encountered was a couple of years ago - I opened up a brand new ITX celeron board and I eventually discovered that one of the RAM slots was bad. The motherboard wouldn't boot with any RAM installed in one of the two RAM slots on the motherboard - remove RAM from that slot, and the system booted fine with RAM in the other slot only. (Of course I had been storing the board for long enough that it was out of warranty, but that's another story...) I suspected a bad solder joint or tin whisker somewhere on the bad RAM slot, but my soldering iron was misplaced a while ago, and a visual inspection of the underside of the board looked OK.
Ram Slot Solder
I have been testing more boards than I used to over the past year, and I have found a number of other boards which have bad RAM slots, so I was wondering how many bad RAM slots others here have run into on otherwise good motherboards.
Also, has anyone ever successfully fixed a bad RAM slot, say with a solder reflow?
So far, in terms of failure modes with bad RAM slots, either any RAM in that slot is not recognized and ignored, or else the system won't boot with any RAM in that slot, either locking up during POST or black screen before POST, sometimes with beeps. Any time I have had memtest rack up errors, I have eventually traced it to an actual bad stick of RAM, but has anyone else noticed bad RAM slots causing other symptoms?
On dual processor Xeon boards I have further findings:- If the blue (primary) RAM slot in a channel is bad, that whole channel is unusable
- If the first blue slot for a CPU is bad, that CPU socket is unusable
- If a non-blue slot is bad, usually only that slot is bad
Ram Slot Soldering Iron
Hi Guys,
I've got an Asus P5B Deluxe motherboard. Today I tried adding some new RAM to take it from 4GB to 8GB. The board is about 6 years' old. I've never used the black RAM slots before, only the yellow ones (2x2GB in slots 1 and 3).
My system only sees 6GB, not 8GB. I've tried various combinations of the RAM, get the same result.
To check the new RAM wasn't defective, I tried it in slot 1, a known good slot. All 4 sticks of RAM worked in slot 1, so the RAM wasn't faulty.
All 4 sticks work in every slot except slot 2 (the first black RAM slot). If I put any stick in slot 2 - old or new - the PC is dead, it won't even boot to the BIOS.
So it looks like I have a defective RAM slot.
Does anyone know of any way to fix this? The board is too old to RMA. I've tried an emery board down the defective slot, and I've tried squirting WD40 down it. No improvement.
Does anyone have any other ideas on how to get that bad slot working?
Thanks!
I've got an Asus P5B Deluxe motherboard. Today I tried adding some new RAM to take it from 4GB to 8GB. The board is about 6 years' old. I've never used the black RAM slots before, only the yellow ones (2x2GB in slots 1 and 3).
My system only sees 6GB, not 8GB. I've tried various combinations of the RAM, get the same result.
To check the new RAM wasn't defective, I tried it in slot 1, a known good slot. All 4 sticks of RAM worked in slot 1, so the RAM wasn't faulty.
All 4 sticks work in every slot except slot 2 (the first black RAM slot). If I put any stick in slot 2 - old or new - the PC is dead, it won't even boot to the BIOS.
So it looks like I have a defective RAM slot.
Does anyone know of any way to fix this? The board is too old to RMA. I've tried an emery board down the defective slot, and I've tried squirting WD40 down it. No improvement.
Does anyone have any other ideas on how to get that bad slot working?
Thanks!